Craftsman gas-powered Weedwackers space equipped with two varieties of cutting heads: a fixed-line head or one optional trimmer head. Craftsman proposal using only brand-name line. Use the eco-friendly line for cutting grass only. Red heat is intended because that grass and little weeds. Install black line for large weeds and tiny brush.
You are watching: How to replace trimmer line on craftsman weedwacker
Fixed-line Heads
With a stubborn brush, clean debris indigenous the cutting head. Look in ~ the cutting head and determine which feet you should use to feed the line. Insert red and also green line right into the holes marked “small.” Feed black color line into the holes marked “large.”
Craftsman gas-powered Weedwackers space equipped with two types of cut heads: a fixed-line head or an optional trimmer head. Usage the environment-friendly line because that cutting grass only.
Insert one end of the heat through among the correct dimension holes in the cut head. Feed it through to about half the size of the line. Insert the other finish of the line into the other hole that the exact same size. Feed it v to a comparable length.
Grasp one finish of the line and insert it through the positioning tunnel, ~ above the exact same side as you inserted that end through the cutting head hole. Perform the exact same with the other end of the line and corresponding placing tunnel.
Grasp both ends of the line and also pull tightly in either direction. Check to check out that the portion of the line between the cutting head feet is tight versus the hub. Check also to watch that both end of the line are around the very same length.
Insert one finish of the line through among the correct dimension holes in the cut head. Insert the other finish of the line right into the other hole that the very same size.
Optional-line Heads
Pull top top the tap switch of the head to eliminate the spool. Set the Craftsman Weedwacker aside. V a stubborn brush, clean any kind of debris indigenous the spool and also hub.
With a ice cream measure and also garden shears or scissors, measure and cut two strands of line, each 12 ½ feet long. Insert the finish of one strand of heat ½ an inch into one that the tiny holes on the spool. Perform the same for the other strand.
Hold the spool in one hand and also grasp both strands of line in the other hand. Wind the strands tightly approximately the spool in the direction suggested by the arrows ~ above the spool. Stop once there are 5 come 7 inch of unwound line left on each strand.
traction on the tap switch of the head to eliminate the spool. Through a stubborn brush, clean any debris native the spool and hub.
Holding the heat tight versus the spool, insert the unwound end of one of the strands into one the the notches top top the spool to hold it in place. Repeat this through the other unwound end. There should be 3 come 5 customs of line extending from each of the notches.
Grasp the Weedwacker hub in one hand. Through the other hand, insert one end of the line extending from a notch v the corresponding exit feet on the hub. Take treatment to not release the heat from the notch. Insert the other line v the other exit hole, so that the two ends the line carry out not cross.
stop the line tight against the spool, insert the unwound finish of one of the strands right into one the the notches on the spool to host it in place. With the other hand, insert one finish of the line stretching from a notch with the equivalent exit hole on the hub.
Place the facility hole in the spool over the drive shaft on the hub. Press the spool top top the hub so the it snaps securely. Grasp one strand of heat in each hand. Pull the strands away from the head until you feeling them release from the notches.
Hold one strand of line and stretch it across to the opposite next of the head. Through scissors or garden shears, cut the size of the heat so the it is no much longer than the diameter the the head. Do the very same with the other strand.
See more: How Many Drops In A Cc - 1 Cubic Centimeter (Cc Cm 3 ) = 20
ar the center hole in the spool end the drive pillar on the hub. Press the spool onto the hub so the it breaks securely.
Aaron Painter started as a garden writer in 1999, and has an ext than 12 year of professional experience in landscaping and also horticulture and also six year in transfer journalism. Painter holds a BA in fixed communication and also horticulture indigenous LSU, and now stays in Nashville, Tenn.